Search results

  1. gCreate

    gMax 2 PRO Mainboard (SKR v2 & v3) Firmware 221107

    [RED_TITLE]Marlin 2 Firmware for gMax 2 PRO[/RED_TITLE] Update 11/7/2022 : MPC replaces PID for temperature control. Unified bed leveling replaces bi-linear bed leveling for a 60% reduction in leveling time Linear advance is utilized for pressure control Junction deviation replaces classic jerk...
  2. gCreate

    gMax 2 PRO Touchscreen Firmware 221107

    Please note the gMax 2 PRO mainboard and touchscreen use different firmware. This is for the touchscreen only. Installation instructions can be found in the gMax 2 PRO user guide found on this forum. Update 11/7/2022 : MPC tuning to replace PID Notifications display correctly Preheat defaults...
  3. gCreate

    gMax 2 3D Files 210729

    A collection of .stl files of replacement parts for the gMax 2 PRO. We recommend printing in CFPLA for best results and with 60% infill and 4 perimeters
  4. gCreate

    gMax 2 PRO 3D Files 210728

    A collection of .stl files of replacement parts for the gMax 2 PRO. We recommend printing in CFPLA for best results and with 60% infill and 4 perimeters
  5. gCreate

    gMax 2 Dual 2in1 Firmware Marlin 1.1.9 (SSR and Regular) 210708

    [RED_TITLE]Marlin 1.1.9 Firmware for gMax 2 Dual 2in1[/RED_TITLE] Zip file contains firmware for printers with the SSR relay as well as the original IoT relay. Make sure to choose the correct firmware when installing. Max temp of hotend is 243° C. DO NOT EXCEED THIS TEMPERATURE. Update...
  6. gCreate

    gMax 2 PRO - Wiring Guide 210722

    Useful guide showing the wiring of the gMax 2 PRO electronics case, touchscreen, extruder and
  7. gCreate

    gMax 2 PRO -User guide 210827

    The user guide is a more comprehensive guide reviewing the features of the printer, maintenance tips, firmware error codes, firmware installation and more. Update 210827: +Added more information about error codes +Added new information regarding updating firmware
  8. gCreate

    gMax 2 PRO - Getting Started Manual 210827

    A useful guide to show some of the features of the printer and walk you through your first print.
  9. gCreate

    gMax 2 PRO - Unboxing Guide 210707

    I useful guide used to unbox and set up the gMax 2 PRO printer.
  10. gCreate

    gMax 2 E3D Hotend Installation

    [RED_TITLE]Installing an E3D Hotend on a gMax 2[/RED_TITLE] Overview You may need to replace the e3d hotend on your gMax 2 and this guide will walk you through the steps to install a fully assembled hotend from our store. Step 1: Raise your extruder by going to "gMax Tools > Raise Z 100mm" or...
  11. gCreate

    gMax 1.5+ Marlin 1.1.9 - SSR Heated Bed Firmware 210414

    [RED_TITLE]Marlin 1.1.9 Firmware - SSR Heated Bed[/RED_TITLE] Only use with the gMax SSR addon and new heated bed. This will not work with the external gMax 1.5+ Keenovo control box without modification. Update 4/14/2021 : First Upload + Added Heated Bed via printer Control + LED light bar...
  12. gCreate

    gMax Prusaslicer Config Files 210915

    As of PrusaSlicer version 2.4 gMax configuration files are now bundled with the program and no longer must be installed separately. Please visit the PrusaSlicer download page and download version 2.4 or newer. To add the gMax profiles in PrusaSlicer go to "Configutation > Configuration Wizard"...
  13. gCreate

    Cura 4.8 Config Files for gMax 3D Printers 201113

    These must only be used with Cura 4.8 https://ultimaker.com/software/ultimaker-cura Installation instructions can be found in the zip file. Upgraded version from 14 to 15. For Single and Dual Extruder gMax Printers.
  14. gCreate

    gMax 2 Marlin Firmware - USE ONLY WITH gMax Solid State Relay (SSR) 200929

    [RED_TITLE]Marlin 1.1.9 Firmware for gMax 2 with Solid State Relay (SSR) ONLY![/RED_TITLE] Update 09/29/2020 : + Adjusted thermal runaway threshold for heated bed. TR will trigger if bed is 6+ degrees outside target temperature for 30 seconds or more. Update 09/18/2020 : +Firmware is for use...
  15. gCreate

    Cura 4.7 Config Files for gMax 3D Printers. 200831

    These must only be used with Cura 4.7. https://ultimaker.com/software/ultimaker-cura Installation instructions can be found in the zip file. Upgraded version from 14 to 15. For Single and Dual Extruder gMax Printers. Definitions: Defines printer Quality: Defines different print quality...
  16. gCreate

    Cura 4.6.2 - gMax 1.5+ and gMax 2 Config Files with Instructions 200806

    [RED_TITLE]gMax 1.5+ and gMax 2 configuration files for Cura 4.6.2.[/RED_TITLE] Installation instructions can be found in the zip file. Upgraded version from 13 to 14 Definitions: Defines printer Quality: Defines different print quality settings Variants: Defines nozzle sizes From what...
  17. gCreate

    NEW Internal Case Fan

    [RED_TITLE]Installing the New Internal Case Fan[/RED_TITLE] Overview One of the newest additions to the gMax 2 is the inclusion of better internal case cooling! Below is a step by step instructional on how to convert and install your electronic case cooling system. Step 1: Power down your...
  18. gCreate

    Cura 4.6.1 - gMax 1.5+ and gMax 2 Config Files with Instructions 200609

    [RED_TITLE]gMax 1.5+ and gMax 2 configuration files for Cura 4.6.1.[/RED_TITLE] Installation instructions can be found in the zip file. Please note Cura 4.6.1 had changed the way configuration files are handled. Definitions: Defines printer Quality: Defines different print quality settings...
  19. gCreate

    Heating Failed

    [RED_TITLE]What does the Heating Failed error mean?[/RED_TITLE] [DIV_CONTAINER=60%]If your gMax is prompting a "Heating Failed" error message on the screen, here's why. If your printer is given the command to heat either the hotend or heated bed, but the temperature does not change at all, then...
  20. gCreate

    Thermal Runaway

    [RED_TITLE]What is a Thermal Runaway?[/RED_TITLE] [DIV_CONTAINER=70%]A Thermal Runaway is an error that occurs when the temperature on your hotend or heated bed has dropped below the expected temperature for over a certain amount of time. If this error occurs, that means there is a problem with...