Search results

  1. M

    gMax 1.5 to gMax 2

    I would love to know if there is a way I can upgrade my gMax 1.5 to gMax 2 Components? I'm willing to pay for upgrades since I have no desire in having a larger printer. Thanks!
  2. M

    Loose Eccentric spacer

    I have one eccentric spacer that I can't seem to tighten, or not sure if It should fit loose. It doesn't wobble but it does rotate freely without any resistance. How do I tighten it?
  3. M

    Leveling X-Axis Arm Calibration Print

    Awesome! ETA? :)
  4. M

    Leveling X-Axis Arm Calibration Print

    Am I missing something? When I print the X-Axis Arm Calibration Print (X-axis probe space ship) it prints way too small. Theres no way of enlarging it either....
  5. M

    Extruder test Jumps on Initial setup Test

    Running the Initial setup script off the SD card files and it gets to the Extruder Test, is it normal for the Extruder to strip or skip filament at about every inch of filament pushed through?
  6. M

    SD Card download for Marlin 1.1.9

    Theres a gMax SD Card Files - Marlin 1.1.8 Firmware is there a SD Card download for 1.1.9 ? or Can we still use the 1.1.8 download?
  7. M

    Gcreate sample print Files

    Hey Guys! I've requested and received some of your 3D printed Sample files that look great! I would like to if possible to get the .Gcode or STL files so I can print them my self and use this as a way to tune my gMax... Im mostly interested in the Injection Mold and the Bracket sample! Thanks!
  8. M

    How to reset Pabystep

    Question, when adjusting the BLTouch the "Hard method" as shown here http://forum.gcreate.com/index.php?threads/adjusting-the-bltouch-z-offset.2035/ Does it matter if I you use a piece of paper as mentioned or the Businesscard method as shown in some other tutorials?
  9. M

    How to reset Pabystep

    Awesome thanks!
  10. M

    How to reset Pabystep

    What im trying to do is for the printer not to use the previous Babystep settings. As its printing I see on the screen the -0.02 Z-offset (I believe its the last babysit settings correct) but then when I go into the Babystepsettings Im expecting it to say -0.02 and its ays 0.00 instead. If I...
  11. M

    How to reset Pabystep

    Wondering how to reset Babystep settings. I basically want to roll the babystep settings back to 0.00. I noticed that while printing the current babystep settings are shown on the print progress screen. Thx!
  12. M

    LCD Flakey when reading from SD

    Wondering if theres a fix for the Flakey/jumpy screen when reading/ navigating files on SD. Thanks!
  13. M

    When to tighten the Anti-Backlash Nut Block

    Sorry I'm so confused. RIght now the screws on my current nut blocks are in their "original position" from when I purchased the printer - where they're not tighten up to add resistance, im confused on why I may need to tighten it. Is this because after some wearing the nut block may become...
  14. M

    When to tighten the Anti-Backlash Nut Block

    Do you mean like dropping on it's own or if with some force by hand?
  15. M

    When to tighten the Anti-Backlash Nut Block

    My printer is a few months old and was wondering how do I know when it's time to tighten or mess with the Anti-Backlash Nut Blocks? I do notice that that one side seem to always seem to be .01MM lower than the other side after a print. I manually adjust the hight and it seem ok after I raise Z...
  16. M

    Missing Screw?

    Ahh I see. ok thanks!
  17. M

    Missing Screw?

    Needed to remove my Hotend for cleaning and noticed that the Extruder bracket thing is missing a screw on the bottom left (Can I order these?) Not sure if it's porously. Also cant really notice it on the photo but with all screws loose the Extruder bracket is CROOKED. Slightly higher on the...
  18. M

    Printer randomly stop mid print

    I'm actually on a Mac...But yes that could be it too. I'll keep exploring it. Thanks!
  19. M

    Printer randomly stop mid print

    Printing via SD card works perfectly which is what I've started doing (I'm actually liking it better despite the extra steps). When I print via USB is when it randomly happens. I've been reading up on it and I'm probably guessing it may be power spikes in my outlet which I wouldn't it doubt it...
  20. M

    Printer randomly stop mid print

    Just did it printing a test STL using Cura. half way through I came back and it was frozen. Hotend still hot and fan running. LCD says Printing and Cura says Printing. I can Pause the print but nothing happens. All I can do now is Cancel the print and it does.