Menu
What's new

Hardware Troublehooting

gCreate managed hardware-based troubleshooting forum
GORDON.LAPLANTE
  • Sticky
MINTEMP or MAXTEMP Issue
Replies
1
Views
8,675
sherpa_chris
GORDON.LAPLANTE
  • Sticky
What Should My First Layer Look Like?
Replies
3
Views
9,630
raykholo
GORDON.LAPLANTE
  • Sticky
When an Endstop is Triggered the Printer Restarts
Replies
0
Views
7,877
GORDON.LAPLANTE
GORDON.LAPLANTE
  • Sticky
Endstop Metal Lever Came Off
Replies
0
Views
7,666
GORDON.LAPLANTE
GORDON.LAPLANTE
  • Sticky
Motors Move in Wrong Direction (Away From Endstops)
Replies
0
Views
7,658
GORDON.LAPLANTE
GORDON.LAPLANTE
  • Sticky
Print Bed Sags at Edges
Replies
0
Views
7,767
GORDON.LAPLANTE
GORDON.LAPLANTE
  • Sticky
Motors Don’t Turn They Only Hum
Replies
0
Views
9,073
GORDON.LAPLANTE
GORDON.LAPLANTE
  • Sticky
LED Light Doesn’t Work on Extruder
Replies
0
Views
9,057
GORDON.LAPLANTE
GORDON.LAPLANTE
  • Sticky
Extruder Fan Doesn’t Work
Replies
0
Views
9,051
GORDON.LAPLANTE
GORDON.LAPLANTE
  • Sticky
Motors Are Very Loud or Electronics Heatsinks Get very Hot
Replies
0
Views
7,798
GORDON.LAPLANTE
GORDON.LAPLANTE
  • Sticky
Where should the table be to start a print?
Replies
0
Views
7,667
GORDON.LAPLANTE
GORDON.LAPLANTE
  • Sticky
In a dual extruder setup, which hotend is which?
Replies
0
Views
7,772
GORDON.LAPLANTE
GORDON.LAPLANTE
  • Sticky
Where does the SD card go?
Replies
0
Views
7,571
GORDON.LAPLANTE
GORDON.LAPLANTE
  • Sticky
LCD screen backlight is slightly on but no text
Replies
0
Views
7,512
GORDON.LAPLANTE
GORDON.LAPLANTE
  • Sticky
LCD screen doesn’t turn on
Replies
0
Views
8,845
GORDON.LAPLANTE
GORDON.LAPLANTE
  • Sticky
What is an “Endstop”
Replies
0
Views
9,079
GORDON.LAPLANTE
L
Filament run-out
Replies
1
Views
6,634
gCreate_Joshua
M
Gmax Board restarts or reboots when connecting..
Replies
1
Views
6,312
mofeliz
D
Gmax 1.5 + upgrade help. Y axis problems.
Replies
6
Views
9,120
gCreate_Joshua
M
Printer randomly stop mid print
Replies
6
Views
7,771
mofeliz
R
Loose Wires/ unreliable connection of wiring harness/ Need help
Replies
1
Views
6,693
gCreate_Joshua
gCreate_Kyle
Powering the BL touch directly from the power supply.
Replies
2
Views
11,961
gCreate_Kyle
gCreate_Kyle
gMax 1.5+ Dual Extruder Alignment
Replies
0
Views
6,960
gCreate_Kyle
GORDON.LAPLANTE
The printer jumps around very fast causing skips
Replies
0
Views
8,701
GORDON.LAPLANTE
GORDON.LAPLANTE
How to install a heater and thermistor on a j-head hotend
Replies
0
Views
7,919
GORDON.LAPLANTE
GORDON.LAPLANTE
One dual edtruder nozzle is too low
Replies
0
Views
7,832
GORDON.LAPLANTE
GORDON.LAPLANTE
Start gcode for dual extruder setups in slic3r
Replies
0
Views
8,950
GORDON.LAPLANTE
You must log in or register to post here.